Table of Contents
Global Limits
Avaliable file descriptors
Other than file descriptors globally used by ze-filter (log files, databases, …) the filters consummes two file descriptors per SMTP connection - one to communicate with the MTA (libmilter) and another one to save the message being handled in the spool. So, roughly speaking, the number of file descriptors in use is the double of the number of connections being handled plus a little fixed quantity (~ 30).
Under Unix, the number of file descriptors being used by a processus simultaneously is upper bounded by :
FD_SETSIZE, if the program uses the select(2) system call, which is the default system call used by libmilter to communicate with the MTA. The default value of this parameter is 1024, but it can be redefined, under some conditions and under some OSs.
libmilter you're using was compiled with one of the following options enabled : SM_CONF_POLL or _FFR_WORKERS_POOL. To do this, you shall add the following line to file devtools/Site/site.config.m4 :
APPENDDEF(`conf_ENVDEF',`-D_FFR_WORKERS_POOL=1') APPENDDEF(`conf_ENVDEF',`-DSM_CONF_POLL=1')
In both cases, all libmilter calls to select(2) are replaced by poll(2) which isn't limited by FD_SETSIZE.
This solution is valid only if the milter itself doesn't call select(2) itself.
- The limit imposed by the operating system. You can get/set this limit with one of the shell commands :
- sh/bash :
ulimit -n - csh/tcsh :
limit descriptors
Checking if the limit is reached is the responsibility of the milter, not libmilter. ze-filter uses the following options to control it. These values are usually fine.
USE_SELECT_LIMIT YES FILE_DESCRIPTORS MAX FD_FREE_SOFT 100 FD_FREE_HARD 50
Maximum simultaneous connections
This value shall usually be set to, no more than, half the limit of the file descriptors available to the filter.
MAX_OPEN_CONNECTIONS 500
CPU load control
If the CPU idle value is less than LOAD_CPU_IDLE_SOFT %, the filter will reject connections from unknown SMTP clients. If the CPU idle value is less than LOAD_CPU_IDLE_HARD %, the filter will stop accepting connections till this value gets up again.
LOAD_CPU_IDLE_SOFT 20 LOAD_CPU_IDLE_HARD 10
Default values are 0 and 0 : no load control
CPU load monitoring
ze-filter logs, once a minute, the server load. It's useful when you need to debug load problems.
# grep "SYSTEM LOAD" /var/log/ze-filter Oct 5 06:27:08 ... SYSTEM LOAD - idle/kernel/user/nice = 99.7 0.2 0.0 0.0 Oct 5 06:28:08 ... SYSTEM LOAD - idle/kernel/user/nice = 99.8 0.1 0.1 0.0 Oct 5 06:29:08 ... SYSTEM LOAD - idle/kernel/user/nice = 99.8 0.2 0.0 0.0 Oct 5 06:30:08 ... SYSTEM LOAD - idle/kernel/user/nice = 99.8 0.2 0.0 0.0 Oct 5 06:31:08 ... SYSTEM LOAD - idle/kernel/user/nice = 99.6 0.3 0.1 0.0 Oct 5 06:32:08 ... SYSTEM LOAD - idle/kernel/user/nice = 99.9 0.1 0.0 0.0 Oct 5 06:33:08 ... SYSTEM LOAD - idle/kernel/user/nice = 99.8 0.1 0.0 0.0 Oct 5 06:34:08 ... SYSTEM LOAD - idle/kernel/user/nice = 99.8 0.1 0.0 0.0 Oct 5 06:35:08 ... SYSTEM LOAD - idle/kernel/user/nice = 99.9 0.1 0.0 0.0 Oct 5 06:36:08 ... SYSTEM LOAD - idle/kernel/user/nice = 99.7 0.2 0.1 0.0
